Easy Access to the North American Market
Make it easier to export your machines to the US and Canada – with product certification from TÜV Rheinland! We will check your systems for compliance with North American legal requirements – at your production facilities and upon installation abroad. Our colleagues in Canada and the US will perform the required FES (“Field Evaluation Service”) compliance procedure. We also assign your products the “field label.” This ensures that you receive the required machine approval from local authorities quickly, easily, and cost-effectively.
Benefits at a Glance
TÜV Rheinland support for individual approvals helps you:
- Avoid problems during the approval process with local inspectors from the AHJ (Authorities Having Jurisdiction)
- Save time, enabling you to deliver working systems on schedule
- Avoid having to make retroactive changes to your machines after they have been installed in the US or Canada
- Increase confidence in the quality and reliability of your machines
It only takes four steps for our experts to help you get approval for your machines:
Before exporting your machines to North America, you contact us and provide us with the technical documentation for your machines, as well as the planned installation location in the USA or Canada.
2. Preliminary Audit
We will inspect your production facilities and perform an on-site preliminary audit of the machine in its ready-for-delivery state and of the corresponding technical documentation too. We will also audit instructions for installation and operations. The audit should be performed early enough, so there is still enough time to make any modifications before shipping.
3. Audit Report
After the preliminary audit, our experts create an audit report. This report will certify that your machine complies with the corresponding product-specific standards that apply in the US or Canada, as well as local requirements. Should this not be the case, you will receive a detailed list of action items that must be dealt with before the final audit. We will send the technical documentation and audit report to the relevant colleague in the US or Canada.
4. Final Audit
Once the system has been installed in the US or Canada, our colleague there will perform a simplified on-site acceptance procedure for the machine. If all the action items have been processed, you will receive a positive FES report, and the machine will be given a field label. The system will then be approved by the local AHJ (Authority Having Jurisdiction) representative.
Legal Standards in the US and Canada
The applicable regulations can be found in articles 90-7, 110-2, and 110-3 of the NEC (“National Electric Code”, and 29 CFR 1910.301 (subpart S) of the OSHA (Occupational Safety and Health Administration). Both organizations require official approval of all electronic devices and systems in the US and Canada. Approval can be proven via a “listing” or a “field evaluation.”
Cables and Wires
Use of Listed Components
Proper conductor protection
Accessibility of live parts
Guarding of moving parts
Suitability of enclosures
Pinching, crushing, falling hazards
Suitability of material
Proper wire bending spaces
Proper Transformer protection
Ground and bonding
Guarding of Live Parts
Accessibility of moving parts
Availability of suitable markings
Proper Motor protection
Required Additional Safety Testing
In addition to relevant construction evaluations, the equipment will also be tested for compliance to safety requirements. The tests may vary depending on the type of equipment. However, some of the most common tests are:
Grounding Continuity Test:
Testing for proper grounding and bonding of the whole equipment.
Dielectric Voltage Withstand Test (Hi Pot Test):
Testing for adequate spacing between conductive parts. Test is performed between primary and ground and primary and secondary of the unit.
Input Current Test:
Measuring the input current of the unit during maximum load operation and evaluating the suitability of protection mechanisms such as fuses, circuit breakers, etc.
Strain Relief Test:
Measuring the strength and suitability of strain relief through push and pull tests.
Test the proper operation of any emergency stops for reliability and proper functioning.
Rain Tests (for outdoor use equipment):
Equipment is exposed to simulated rain conditions for up to four hours. Following the test, the equipment is inspected for ingress of water and tested for dielectric breakdown and insulation resistance.
Tests the suitability and performance of all interlocks giving access to live parts and moving components.
Legal Standards in the US and Canada
The applicable regulations can be found in articles 90-7, 110-2, and 110-3 of the NEC (“National Electric Code”, and 29 CFR 1910.301 (subpart S) of the OSHA (Occupational Safety and Health Administration). Both organizations require official approval of all electronic devices and systems in the US and Canada. Approval can be proven via a “listing” or a “field evaluation”.
- A Nationally Recognized Testing Laboratory accredited by OSHA
- An Inspection Body (IB) and a Certification Body (CB) accredited by the Standards Council of Canada (SCC)
- Accepted throughout the world as one of the largest international testing laboratories.
- Accepted in jurisdictions throughout the United States
- Member of IAEI (International Association of Electrical Inspectors)
- Member of ICC (International Code Council)
- Member of ACIL (American Council of Independent Laboratories)
Our Customers include:
- Machinery manufacturers
- Tool manufacturers
- ITE (Information Technology Equipment) Manufacturers
- Telecommunications & Audio/Video Manufacturers
- Medical Equipment manufacturers and users (Hospitals & Medical Offices)
- Semiconductor manufacturers and users
- Food Preparers & Processors
- Printers & Packagers
- Electrical Contractors
- Industrial & Commercial Consultants
- And Much More...