Chile - Electric Vehicles´ Chargers Installation in Homes, Public Roads, Buildings, etc..

​On December 17, 2020, the Electricity and Fuel Board (SEC), under the Ministry of Energy, released Resolution "Exenta" the proposed rule establishing a regime for the authorization of products used in the infrastructure for the recharging of electric vehicles.

As of April 15, 2021, must have prior authorization from the Superintendence of Electricity and Fuels while the respective protocols do not apply, according to the requirements contained in the file attached (see link) that must be submitted.

Standards related:

 - IEC 61851-1 2017 Electric vehicle conductive charging system - Part 1: General requirements;

- EC 61851-23 2014 - Part 23: DC electric vehicle charging station;

- IEC 62196-1 2014 Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 1: General requirements;

- IEC 62196-2 2016 Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 2: Dimensional compatibility and interchangeability requirements for a.c. pin and contact-tube accessories;

- IEC 62196-3 2014 Plugs, socket-outlets, vehicle connectors and vehicle, inlets - Conductive charging of electric vehicles - Part 3: Dimensional compatibility and interchangeability requirements for d.c. and a.c./d.c. pin and contact-tube vehicle couplers;

- IEC 61851-21-2 2018 Part 21-2: Electric vehicle requirements for conductive connection to an AC/DC supply- EMC requirements for off-board electric vehicle charging systems;

- IEC 62752 2018 In-cable control and protection device for mode 2 charging of electric road vehicles (IC-CPD);

- IEC 62893-1 2017 Charging cables for electric vehicles of rated voltages up to and including 0,6/1 kV - Part 1: General requirements;

- IEC 62893-2 2017 Charging cables for electric vehicles of rated voltages up to and including 0,6/1 kV - Part 2: Test Methods;

- IEC 61557-8 2014 Electrical safety in low voltage distribution systems up to 1000V a.c. and 1500V d.c.-Equipment for testing, measuring or monitoring of protective measures - Part 8: Insulation monitoring devices for IT systems;

- ISO 15118-1 2019 Road vehicles-vehicle to grid communication interface - Part 1: General information and use - case definition;

- ISO 15118-2 2014 Road vehicles -- Vehicle-to-Grid Communication Interface -- Part 2: Network and application protocol requirements;

- ISO 15118-3 2015 Road vehicles -- Vehicle to grid communication interface - Part 3: Physical and data link layer requirements;

- ISO 15118-4 2018 Road vehicles -- Vehicle to grid communication interface - Part 4: Network and application protocol conformance test;

- ISO 15118-5 2018 Road vehicles -- Vehicle to grid communication interface - Part 5: Physical layer and data link layer conformance test;

- ISO 15118-8 2018 Vehicle to grid communication interface - Part 8: Physical layer and data link layer requirements for wireless communication;

- GB/T 20234.1 2015 Connection set for conductive charging of electric vehicles - Part 1: General requirements;

- GB/T 20234.3 2015 Connection Set for Conductive Charging of Electric Vehicles - Part 3: DC Charging Coupler;

- GB/T 27930 2015 Communication Protocols between Off-Board Conductive Charger and Battery Management System for Electric Vehicle;

- GB/T 18487.1 2015 Electric vehicle conductive charging system - Part 1: General Requirements;

- GB/T 18487.2 2017 Electric vehicle conductive charging system - Part 2: EMC requirements for off-board electric vehicle supply equipment.

Note: For the application of this section, UNE, UL, JEVS standards or equivalent standards may be used instead of the IEC standards. The standards that may be used to replace the indicated standards must be in Spanish or, alternatively, in English.